FM SERIES PHOTOELECTRIC SENSOR

Opposed mode: sn=3m / 30m
Diffuse mode: sn=300mm / 380mm
Retroreflective mode: sn=5m
Polarized reflective mode: sn=2m
Convergent mode sn= 16mm / 43mm
House size: 53x12x30mm / 39X12X30mm
FM SERIES PHOTOELECTRIC SENSORS SPECIFICATIONS(DC)

SENSING MODE/

ITEM
DC
OPPOSED MODE
RETRO REFLECTIVE MODE
DIFFUSED MODE
E
R
Sensing Range
see each mode
Hysteresis
-
Operating Voltage
10~30v
Ripple
< ¡¾ 20%
Voltage Drop
-
<2.0V at 150mA
Max Load Current
-
150mA
No Load Current
<25mA
Min. Load Current
-
5mA
Leakage Current
-
<1mA
Output Configuration
Bipolar: One current sourcing (PNP) and one current sinking (NPN) open-collector
transistor
Indicators Red indicator LED on rear or sensor is on when the load is energized
Adjustments LIGHT/DARK OPERATE select switch, and 15-turn slotted brass screw GAIN (sensitivity) adjustment potentiometer(clutched at both ends of travel). Both controls are located on rear panel of sensor and protected by a gasketed, clear acrylic cover.
Transiet protection yes
Resverse polarity protection yes
Short Circuit Protection yes
Over Load current protection >180mA
Output response time 1ms or 0.3ms(High-speed TYPE)
Construction Reinforced thermoplastic polyester housing, totally encapsulated, o-ring sealing, acrylic lenses, and stainless screws.
Environmental rating IP67
Operating Conditions Temperature: -20 ¡ÆCto +70 ¡ÆC, Maximum relative humidity: 90% at 50OC
EMC IEC 60947-5-2, Parts 7.2.6.1. 2. 3 or RFI>3V/m(in 30-1000MHZ), EFT>1KV, ESD>4KV(contact)
Voltage Withstand Ability IEC 60947-5-2, Part 8.3.3.4 or 500VDC for one min, between all supply terminals connected together and enclosure
Insulation Resistance >20M¥Ø , with 500V DC megger between all supply terminals connected together and enclosure
Vibration Resistance IEC 60947-5-2, Part 7.4.2 or 10-55HZ, 1.0mm amplitude in x , y and z directions for 30 min
Shock Resistance IEC 60947-5-2, Part 7.4.1 or 30g, 11ms in x , y and z directions for six time each
FM SERIES PHOTOELECTRIC SENSORS SPECIFICATIONS(AC)

SENSING MODE/

ITEM
AC
OPPOSED MODE
RETRO REFLECTIVE MODE
DIFFUSED MODE
E
R
Sensing Range
see each mode
Hysteresis
-
  
Operating Voltage
24~240V AC (50/60HZ)
Output configuration
SPST MOSFET solid-state relay with either normally closed or normally open contact (light/diark operate selectable; 3-wire hookup
Voltage Drop
-
<10V at 200mA
Max Load Current
-
<200mA
No Load Current
25mA
<1.7mA
Min. Load Current
-
<5mA
Leakage Current
-
<1.7mA
Transiet protection

yes

Short Circuit Protection -
yes
Over Load current protection -
>220mA
Response Time 2ms 8ms 4ms 8ms
Construction Reinforced thermoplastic polyester housing, totally encapsulated, o-ring sealing, acrylic lenses, and stainless screws.
Adjustments LIGHT/DARK OPERATE select switch, and 15-turn slotted brass screw GAIN (sensitivity) adjustment potentiometers (clutched at both ends of travel). Both controls are located on rear panel of sensor and protected, clear acrylic cover.
Indicators Red indicator LED on rear or sensor is on when the load is energized
Environmental rating IP67
Operating Temperature Temperature: -20C to +70C, Maximum relative humidity: 90% at 50C
EMC IEC 60947-5-2, Parts 7.2.6.1. 2. 3 or RFI>3V/m(in 30-1000MHZ), EFT>1KV, SD>4KV(contact)
Voltage Withstand Ability IEC 60947-5-2, Part 8.3.3.4 or 500VDC for one min, between all supply terminals connected together and enclosure
Insulation Resistance >20M¥Ø , with 500V DC megger between all supply terminals connected together and enclosure
Vibration Resistance IEC 60947-5-2, Part 7.4.2 or 10-55HZ, 1.0mm amplitude in x , y and z directions for 30 min
Shock Resistance IEC 60947-5-2, Part 7.4.1 or 30g, 11ms in x , y and z directions for six time each
FM SERIES PHOTOELECTRIC SENSORS CONNECTION DIAGRAM
Receiver: NPN / PNP output wiring diagram (DC)
____________________
Emitter wiring diagram (DC)
_________________________
Receiver: wiring diagram (AC)
____________
Emitter wiring diagram (AC)
_______-_____
FM SERIES PHOTOELECTRIC SENSORS DIMENSIONS
DC SENSOR
AC SENSOR